Haymes Rustlock Waterbased Grey Primer 1 Litre

Primer

The RustLock Primer is an easy to use, water based primer specifically formulated to ‘lock-out’ corrosion on a wide range of metals. It can be used on surfaces including sheet metal, castings, wrought iron and steelwork. When applied correctly and over coating with the RustLock finishing coat it is guaranteed for 7 years to prevent corrosion.

GENERAL DESCRIPTION An easy-to-use, water-based primer specifically formulated to ‘lock-out’ corrosion on a wide range of metals. Applied correctly, RustLock is guaranteed for 7 years*. USES Suitable on sheet metal, castings, wrought iron and steelwork. This product is not recommended for roofing or automotive use.  

COVERAGE Up to 14 square metres per litre depending upon surface porosity and application method. APPLICATION Roller, brush or airless spray.

PROVIDE ADEQUATE VENTILATION DURING USE. DRYING TIMES Touch Dry Time - 20 minutes. Recoat Dry Time - 2 hours. Drying times refer to normal conditions (25°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary.

DO NOT USE IN TEMPERATURES BELOW 10°C OR ABOVE 30°C. DANGEROUS GOODS CLASSIFICATION Not classified as Dangerous Goods.

SURFACE PREPERATION Previously Painted Surfaces: Scrape off loose and flaking paint and make sure the remainder is firmly attached. Sand glossy surfaces and enamels thoroughly and wipe clean. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with RustLock Derustit Rust Converter as per directions. Prime treated and bare areas with one coat RustLock Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of RustLock Anti- Corrosive Metal Primer.

BARE STEEL, WROUGHT IRON: Remove all grease, dirt and other surface contaminants. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with RustLock Derustit Rust Converter as per directions. Prime treated and bare areas with one coat RustLock Anti-Corrosive Metal Primer.

ZINCALUME® AND GALVANIZED IRON: Remove all grease, dirt and other surface contaminants. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with RustLock Derustit Rust Converter as per directions. Avoid applying RustLock Derustit Rust Converter to zinc coated areas. Prime treated and bare areas with one coat RustLock Anti-Corrosive Metal Primer. ALUMINIUM: Remove all grease, dirt and other surface contaminants.

FINISHING Apply two coats of RustLock Water-Based Enamel Gloss Metal Paint by brush, roller or airless spray. Allow to dry for 2 hours before recoating. THINNING & CLEAN UP May be thinned with up to 100ml of water per litre for spraying. Apply subsequent coat/coats unthinned. Clean equipment with water immediately after use.

PAINTING CONDITIONS Do not apply if the temperature is below 10°C. In hot weather, avoid painting in direct sunlight. Do not apply is rain or dew is likely during the drying period. CARE AND MAINTENANCE New paintwork should not be exposed to steam or condensation for 48 hours. Protect the coating from abrasive contact for 7 days. This product should be washed only with a mild detergent solution. Wash down periodically to refresh and preserve the coating.

STORAGE Protect from extremes of temperature. Store between 5°C and 30°C. WARRANTY: Haymes guarantees that the RustLock paint system will prevent the development of rust on properly prepared surfaces, as per Haymes’ instructions, for a period of 7 years. Damage to the surface voids an warranty, explicit or implied. If the Haymes RustLock system fails to prevent rust formation within 7 years of application, Haymes will provide sufficient product to recoat affected areas free of charge. This warranty does not cover any labour charges.

Q U I C K C H E C K

Exterior Water Wash Up Brush,

Roller or Airless Spray

Recoat – 2 hours

Rustlock Water-Based Anti- Corrosive Metal Primer Product Data Sheet V1.00 29/06/2009 ©Copyright 2001 Henry Haymes Pty Ltd Page 2 of 2

PRECAUTIONS  Safety Directions: Keep out of reach of children. Avoid contact with skin and eyes and inhalation of vapours. Wear suitable protective clothing, eye protection and impervious gloves when mixing and using. Handling and usage of this product must be carried out under well ventilated conditions that prevent inhalation of vapours.. 

First Aid Directions: If affected by inhalation, remove to fresh air. If breathing difficulty persists or occurs later, consult a doctor. If swallowed, drink plenty of water and seek medical advice. Contact a doctor or Poisons Information Centre (Phone 13 1126). If skin contact occurs, remove contaminated clothing and wash skin thoroughly with soap and water. If irritation occurs seek prompt medical advice. In case of eye contact, hold eyes open and flush with running water for at least 15 minutes and seek medical advice.

NOTE: Further information is available in the form of Material Safety Data and Product Information Sheets from your local Haymes Paint Distributor or Freecall Haymes Paint on 1800 033 431. We are continually updating materials and methods, so please ensure you have the latest information. 

Protect Our Environment: Ensure paint does not get into gutters or drains. Retain in a marked sealed container for future use or disposal via special chemical waste collection programs. Dried empty containers can be recycled and should be disposed of via council recycling facilities. Do not re-use empty containers. For best results, preparation is vitally important. When repainting, always ensure that the adhesion of old paint is sound before proceeding.